DFS Update and High Grade Ore Sweeped from Gold Mine
Released
Released
Announcement PDF
4 March 2022
ASX ANNOUNCEMENT
DFS UPDATE AND HIGH GRADE ORE SWEEPED FROM NEW
HISTORICAL MINES
•
•
•
•
High-Grade assayo Beverly Hills sweepings grabs – 15.79g/t Au and 4.37g/t Au
o Beverly Hills chip samples – 11.79g/t Au
o Desire sweepings grabs – 14.27g/t Au and 10.79g/t Au
Feasibility study 80% completion:
o Metallurgical testwork nearing completion
o Mine Designs
o Geotechnical investigation
o Underground investigations
Plant demolition in progress in preparation for new plant construction
Environmental Scoping Report submitted for MR83
TGME Plant at 70% demolition
(Note Gold Room, Elution Circuit, Mill, 3 Pre-conditioning tanks, all existing stores, and
administration building will not be demolished)
Theta Gold Mines Limited (“Theta Gold” or “Company”) (ASX: TGM, TGMO | OTCQB: TGMGF)
is pleased to announce the progress made with its underground gold project Feasibility study
(“FS”), environmental approvals, and preparation for plant construction. The Beta, Frankfort,
CDM, and Rietfontein mines are collectively referred to as TGME Underground (UG) Project.
Theta Gold Mines Limited ABN 30 131 758 177
Suite 80, Level 35 (Servcorp), International Tower One, 100 Barangaroo Avenue, Sydney NSW 2000
Tel: +61 2 8046 7584 Email: info@thetagoldmines.com
www.thetagoldmines.com
Discoveries made recently, namely Beverly Hills and Desire mines, form part of the 43
historical mines under management. Both have experienced very little modern exploration.
We now know through underground plans and mine surveys, Desire is one of the larger
underground mining complexes in the Goldfield with historic underground workings
extending kilometers.
The Desire Mine complex is 1.5km on strike and 3.2km on dip, making this one of the largest
unexplored old mines under management. The Desire Mine complex exploited the Portuguese
Reef, producing approximately 170Koz Au from 563Kt, grading 9.41 g/t Au. The mine area
overlaps parts of the farms Graskop 564KT, Desire 563KT (10167 MR), Ponieskrans 543KT (83
MR), and Grootfontein 562KT (341 MR).
Locality Plan of Desire Mine Workings
2
Theta’s Chairman Bill Guy commented: “The results of the grab samples taken at both Desire
and Beverly Hills Mines are very encouraging as the results indicate high grades within these
Mines. The Beverly Hills Mine is currently planned and scheduled as part of the Frankfort Mines
LoM.
The Desire Mine host a large flat reef system, the results of the high grade grab samples are
consistent with historical mine evaluation plans. The Desire Mine will undergo further sampling
and test work as part of the continuous exploration of the 43 Historical Mines under
management.
The permanent onsite team will continue with sampling and exploration work. The team is on
track to complete the DFS in Q2 2022. The geotechnical investigations were conducted
according to plan with encouraging results. Metallurgical test work continued with bulk
samples (approx. 1.5 tons per Mine) taken from , Rietfontein and CDM Mines. These samples
are currently at the Laboratory.
The team has completed the final permitting scoping phase for Mining Right 83. The final
scoping report will now be assessed by the DMRE and once approved the process will move to
the Environmental Impact Assessment (EIA) phase of the permitting process.
Summary
1. Feasibility study progress
1.1. Metallurgical test work nearing completion
The underground gold project Definitive Feasibility Study (“DFS”) that started in September
2021 is progressing well, currently at 65% completion with final completion expected in Q2
2022. In support of the FS, metallurgical test work, mine designs, geotechnical studies, and
underground investigations are now nearing completion.
In addition to the metallurgical test work undertaken for the Preliminary Feasibility Study
(“PFS”), a further bulk sample was taken from Frankfort Mine by trenching the reef
accumulation generated by the trial mining, providing a representative sample in terms of ore
variability and particle size distribution. The PFS study included a single rougher flotation stage
and indicated limited sensitivity to grind. It was decided to conduct additional flotation test
work confirming the plant process flow. The flotation trials are complete and largely support
the PFS results. The carbon and sulphide flotation products are currently submitted for
analysis, which will allow for final circuit mass balancing and financial modeling. These results
are expected in the first week of March 2022.
3
Carbon flotation indicating high flotation kinetics
The sulphide flotation kinetics are extremely rapid indicative of a largely sulphide orebody
1.2. Mine Designs
The overall mine designs are progressing well with the ventilation studies for Beta, CDM and
Frankfort completed following the mine design and mining schedules. The surface
infrastructure of the mining operations is in the process of being aligned and adjusted to
recommended environmental layouts. The optimisation of the mining power requirements
has been completed and, informing the bulk power supply infrastructure design.
4
1.3. Geotechnical investigation
A comprehensive gravity survey was conducted by Applied Scientific Services and
Technologies at Frankfort, Beta and CDM mines, and at the central Tailings Storage Facility
(TSF). The gravity surveys were carried out, generally, on a 10 meters grid. Thirty-three
percussion boreholes were drilled, in accordance with SANS 1936-2 standards. The boreholes
were drilled to a depth of 60 meters, with chip samples taken at 1-meter intervals and logged
in accordance with the standard procedure proposed by Brink and Bruin. The results of the
geotechnical investigation will be submitted to the Council of Geoscience for comments and
recommendations for inclusion in final TSF and surface infrastructure designs.
Boreholes drilled at TSF and Beta Mine
1.4. Underground investigations
Underground expeditions are continuously conducted by the mining team into the four mines
that form part of the phase 1 project, as well as other mines that will be included in
subsequent phases of development. Multiple access points via existing adits are therefore
investigated to determine safe accessibility, and where old reef development and stoping
areas are accessed, the areas are made safe and sampled for grade verification, metallurgical
testwork and rock engineering assessments.
Most of these workings haven’t been actively mined since the pre-world-war periods, while a
few were last mined around 2008. Most of the stope panels are still accessible due to the
excellent ground conditions and support provided by stone packing, and more recent timber
support. Several haulages, reef drives, and stope panels are found to still contain large
amounts of broken ore, which provide opportunities to complement primary mining tons with
cheap, immediately available ore that can be fed to the plant upon commissioning.
Apart from the continuous verification of favourable mining conditions, another positive
outcome of investigations is that only limited flooding of the old mines took place. This is due
5
to the multiple access points and flat nature of the reef, resulting in limited water
accumulation. Access ways will be rehabilitated and re-equipped before mining will
commence.
Note: Historical plans can be referenced and orientated from surface openings and internal markers still present
in the old mines.
Historical Plans mapping out routes during underground investigations
Top Rho reef band
6
Bottom Rho reef band
The Rho Reef is one of over 40 historically exploited reef systems in the Goldfield. Historic
Rho Reef production was 670koz Au from 2.7mt at a head grade of 7.70 g/t Au. Originally
correlated with the Lower Theta Reefs on Theta Hill, the Rho Reef is now known to locate
stratigraphically higher and commonly manifests as two bedding parallel reefs with an
approximate 3m parting. Historic mining stretches over a distance of 4 km northwards
covering the Peach Tree Creek, Dukes Hill, Clewer, and Morgenzon workings. A largely
unexplored 7km strike exploration area of interest exists north from Morgenzon to the
Frankfort workings (see below).
Rho Reef exploration area of interest north from Morgenzon to Frankfort Mine
7
2. Plant demolition in progress in preparation for new plant construction
As part of the preparation for the installation of the first phase new gold plant, TGME has
appointed the services of Jet Demolition to remove the redundant plant equipment. The
process started in the 2nd week of January 2022. Specialized equipment is utilized for
demolition, after which it is reduced in size and made ready for transport to scrap merchants.
The project is now complete.
Plant prior to demolition
Plant at 70% demolition
8
3. Sampling of old Mines
As part of TGM’s exploration strategy ore samples are being taken at prioritised old mines.
Initial samples taken at Beta South Mine, have been delivered to Gold 1 laboratories for
analysis with results expected towards the end of February 2022. Grab samples taken at
Beverly Hills and Desire mine were from old broken ore (sweepings) left in the stope panels.
Random samples are taken from this broken ore where safe entry permits into the old stope
panels. Samples are collected at the top, middle, and bottom of the stope panel. These
samples are then delivered to Gold 1 or SGS laboratories for evaluation. The more chip channel
samples at Frankfort Beverly Hills Mine are taken on a 12-meter grid spacing, channels cut into
the rock from top hangingwall contact to bottom footwall contact. The 25cm between the two
parallel cuts is chipped out, bagged, and transported to the laboratories.
Preliminary assay results are shown below. Further sampling inclusive of bench scale
amenability to gravity and flotation concentration is in progress.
o Beverly Hills sweeping grab samples – 15.79 g/t Au and 4.37g/t Au
(WGS84 UTM 271354E; 7255302 S)
o Beverly Hills chip samples – 11.79g/t Au
o Desire sweeping grab samples – 14.27g/t Au and 10.79g/t Au
(WGS84 UTM 276162E; 7240496 S)
Frankfort Bevetts Reef Au g/t and locality of Berverly Hills MET Testwork Sample
9
Desire Mine locality and site of metallurgical sample
10
4. Environmental Scoping Report submitted
The final scoping report for the environmental authorisation permitting process for the 83 MR
underground project was submitted to the Department of Mineral Resources and Energy
(DMRE) on 3 February 2022.
Final scoping report delivered to the DMRE on 3 February 2022
Various stakeholder meetings took place before the submission of the final scoping report as
part of the required public participation process. A very successful open day was held in
Pilgrims Rest on 15 January 2022 with a good turnout of almost 70 people from the community
and various interested parties. Feedback from the open day was very positive and the
community is excited about the job opportunities and economic upliftment that will be
created by the project. Overall the sentiment was positive towards the proposed project. With
the significant turnout at the open day, adding to numerous other consultation meetings that
were held with interested and affected parties, the procedural requirement to consult widely
during the scoping phase has been satisfied.
Open day consultation meeting held on 15 January 2022
The final scoping report will now be assessed by the DMRE and once approved the process
will move to the Environmental Impact Assessment (EIA) phase of the project.
11
This announcement was authorised for release by Mr Bill Guy, Chairman.
For more information please visit www.thetagoldmines.com or contact:
Bill Guy, Chairman
Theta Gold Mines Limited
T: + 61 2 8046 7584 E: billg@thetagoldmines.com
Webpage: www.thetagoldmines.com
https://twitter.com/ThetaGoldMines
https://www.linkedin.com/company/thetagoldmines/
COMPETENT PERSONS STATEMENT
Exploration Results
The information in this press release relating to Exploration results is based on, and fairly reflects,
the information and supporting documentation compiled by Mr Phil Bentley (MSc (Geol); MSc
(Minex), Pr. Sci.Nat No 400208/05, FGSSA) a consultant to the Company and a member of the South
African Council for Natural Scientific Professions.
ABOUT THETA GOLD MINES LIMITED
Theta Gold Mines Limited (ASX: TGM | OTC: TGMGF | FWB: 3LM) is a gold development company that
holds a range of prospective gold assets in a world-renowned South African gold mining region. These
assets include several surface and near-surface high-grade gold projects which provide cost
advantages relative to other gold producers in the region.
Theta Gold’s core project is located next to the historical gold mining town of Pilgrim’s Rest, in
Mpumalanga Province, some 370km northeast of Johannesburg by road or 95km north of Nelspruit
(Capital City of Mpumalanga Province). Following small scale production from 2011 – 2015, the
Company is currently focussing on the construction of a new gold processing plant within its approved
footprint at the TGME plant, and for the processing of the initial ore reserves.
The Company aims to build a solid production platform to over 160kozpa based primarily around
shallow, open-pit or adit-entry shallow underground hard rock mining sources. Theta Gold has access
to over 43 historical mines and prospect areas that can be accessed and explored, with over 6.7Moz
of historical production recorded.
Theta Gold holds 100% issued capital of its South African subsidiary, Theta Gold (SA) Pty Ltd (“TGSA”).
TGSA holds a 74% shareholding in both Transvaal Gold Mining Estates Limited (“TGME”) and Sabie
Mines (Pty) Ltd (“Sabie Mines”). The balance of shareholding is held by Black Economic Empowerment
(“BEE”) entities as part of the country’s ESG initiatives. The BEE shareholding in TGME and Sabie Mines
is comprised of a combination of local community trusts, an employee trust and a strategic
entrepreneurial partner.
12
DISCLAIMER
This announcement has been prepared by and issued by Theta Gold Mines Limited to assist in
informing interested parties about the Company and should not be considered as an offer or invitation
to subscribe for or purchase any securities in the Company or as an inducement to make an offer or
invitation with respect to those securities. No agreement to subscribe for securities in the Company
will be entered into on the basis of this announcement.
This announcement may contain forward looking statements. Whilst Theta Gold has no reason to
believe that any such statements and projections are either false, misleading or incorrect, it does not
warrant or guarantee such statements. Nothing contained in this announcement constitutes
investment, legal, tax or other advice. This overview of Theta Gold does not purport to be all inclusive
or to contain all information which its recipients may require in order to make an informed assessment
of the Company’s prospects. Before making an investment decision, you should consult your
professional adviser, and perform your own analysis prior to making any investment decision. To the
maximum extent permitted by law, the Company makes no representation and gives no assurance,
guarantee or warranty, express or implied, as to, and take no responsibility and assume no liability for,
the authenticity, validity, accuracy, suitability or completeness of, or any errors in or omissions, from
any information, statement or opinion contained in this announcement. This announcement contains
information, ideas and analysis which are proprietary to Theta Gold.
FORWARD LOOKING AND CAUTIONARY STATEMENTS
This announcement may refer to the intention of Theta Gold regarding estimates or future events
which could be considered forward looking statements. Forward looking statements are typically
preceded by words such as “Forecast”, “Planned”, “Expected”, “Intends”, “Potential”, “Conceptual”,
“Believes”, “Anticipates”, “Predicted”, “Estimated” or similar expressions. Forward looking
statements, opinions and estimates included in this announcement are based on assumptions and
contingencies which are subject to change without notice, and may be influenced by such factors as
funding availability, market-related forces (commodity prices, exchange rates, stock market indices
and the like) and political or economic events (including government or community issues, global or
systemic events). Forward looking statements are provided as a general reflection of the intention of
the Company as at the date of release of the document, however are subject to change without notice,
and at any time. Future events are subject to risks and uncertainties, and as such results, performance
and achievements may in fact differ from those referred to in this announcement. Mining, by its
nature, and related activities including mineral exploration, are subject to a large number of variables
and risks, many of which cannot be adequately addressed, or be expected to be assessed, in this
document. Work contained within or referenced in this report may contain incorrect statements,
errors, miscalculations, omissions and other mistakes. For this reason, any conclusions, inferences,
judgments, opinions, recommendations or other interpretations either contained in this
announcement, or referencing this announcement, cannot be relied upon. There can be no assurance
that future results or events will be consistent with any such opinions, forecasts or estimates. The
Company believes it has a reasonable basis for making the forward-looking statements contained in
this document, with respect to any production targets, resource statements or financial estimates,
however further work to define Mineral Resources or Reserves, technical studies including feasibilities,
and related investigations are required prior to commencement of mining. No liability is accepted for
any loss, cost or damage suffered or incurred by the reliance on the sufficiency or completeness of the
information, opinions or beliefs contained in this announcement.
13
The Feasibility Study referred to in this announcement is based on technical and economic
assessments to support the estimation of Ore Reserves. There is no assurance that the intended
development referred to will proceed as described, and will rely on access to future funding to
implement. Theta Gold Mines believes it has reasonable grounds the results of the Feasibility Study.
At this stage there is no guarantee that funding will be available, and investors are to be aware of any
potential dilution of existing issued capital. The production targets and forward-looking statements
referred to are based on information available to the Company at the time of release, and should not
be solely relied upon by investors when making investment decisions. Theta Gold cautions that mining
and exploration are high risk, and subject to change based on new information or interpretation,
commodity prices or foreign exchange rates. Actual results may differ materially from the results or
production targets contained in this release. Further evaluation is required prior to a decision to
conduct mining being made. The estimated Mineral Resources quoted in this release have been
prepared by Competent Persons as required under the JORC Code (2012). Material assumptions and
other important information are contained in this release.
14
Appendix A Northern Tenement Map
15
APPENDIX B
Phase 1 UG Project Mine Plans
Beta North
Beta Mine Complex
Beta Central
Beta South
CDM Mine Complex
Dukes Mine
Clewer Mine
Morgenzon Mine
16
APPENDIX C
JORC Checklist – Table 1 Assessment and Reporting Criteria
Criteria
Explanation
Nature and quality
of sampling (e.g.
cut channels,
random chips, or
specific specialised
industry standard
measurement tools
appropriate to the
minerals under
investigation, such
as down hole
gamma sondes, or
handheld XRF
instruments, etc.).
These examples
should not be taken
as limiting the broad
meaning of
sampling.
SECTION 1: SAMPLING TECHNIQUES AND DATA
Detail
Sampling types discussed in this section mainly pertain to historical data with the exception of the
Theta
Project subsequent to the 2017-2019 drilling campaign. Drilling data sampling types include diamond,
reverse circulation (“RC”), percussion and auger drilling. Other sampling data types include
underground
channel chip sampling (as individual sample section composite data points on plans or as development
or stope face composite stretch values), grab sampling as well as trench and sample pit sampling for
bulk
sampling for the purposes of size fraction analysis.
The table below outlines the types of sampling data collected or utilised in the Mineral Resource or
Exploration Target estimates for each of the Project Areas.
Project Area
Rietfontein
Rietfontein
Beta
Beta
Frankfort
Bevetts and
Theta
Clewer, Dukes
Hill & Morgenzon
Rho
Olifantsgeraamte
Olifantsgeraamt
e
Vaalhoek
Vaalhoek and
Thelma Leaders
Glynn’s
Lydenburg
Glynn's
Columbia Hill
(remaining)
Hermansburg
DG1
DG2
Beta, Shale,
Lower Theta,
Upper Theta,
Lower Rho,
Upper Rho and
Bevetts
Rho, Shale and
Shale Leaders
Eluvial
Eluvial
Eluvial
DG5
Eluvial
Theta Project
(Theta Hill,
Browns Hills and
Iota section of
Columbia Hill)
Sampling
techniques
Glynn’s
Lydenburg TSF
Blyde TSFs (1, 2,
3, 3a, 4, 5)
TGM Plant
Vaalhoek, South
East (DGs),
Peach Tree,
Ponieskrantz,
Dukes Clewer
a)
Reef
Sampling Data Types
Drillhole Data
Channel Chip Sample Data
Drillhole Data
Channel Chip Sample Data
Drillhole Data
Channel Chip Sample Data
Drillhole Data
Channel Chip Sample Data
Drillhole Data
Channel Chip Sample Data
Drillhole Data
Channel Chip Sample Data
Stretch Values
Drillhole Data
Channel Chip Sample Data
Stretch Values
Drillhole Data
Trench Sampling Data
Channel Chip Sample Data
Drillhole Data
Channel Chip Sample Data
RC Drillhole Data
RC Drillhole Data
RC Drillhole Data
Grab Samples
RC Drillhole Data
Tailings
Auger Drillhole Data
Tailings
Auger Drillhole Data
Tailings
Auger Drillhole Data
Bulk Sampling Data
Trench Sampling Data
Rock Dumps
Sampling Pit Data
Channel Chip Sampling Data:Historical (Pre-1946) chip sample values were captured in ‘pennyweight’ (dwt) units for gold
content and in inches for channel width. The quality of the chip samples could not be ascertained
due to the historical nature there-of; however, it should be noted chip sampling is a wellestablished sampling method in the underground South African mining industry. The sampling
activity on the mines was usually managed by each mine’s survey department and were usually
conducted to specific company-wide standards.
More recent chip sample values were captured as cm.g/t content values and channel widths were
recorded in centimetres as is the case at Frankfort while under ownership of Simmer & Jack Mines
Limited. During 2008, Minxcon audited the chip sampling procedure as employed by Simmer &
Jack and found the procedures employed to be of industry standard.
b)
Stretch Values:In some instances (such as at Vaalhoek and Glynn’s Lydenburg) in areas where original sample
plans were not available, stretch value plans recording a composite content and channel width
17
Criteria
SECTION 1: SAMPLING TECHNIQUES AND DATA
Detail
value for a stope length or development end were available and included in the database. The
integrity of these plans as a source of grade information has been proven in other areas on the
same mines where both chip sample plans and stretch value plans were available and were
compared. It was found that the correlation to old sampling has been representative of the stretch
values in these areas.
Explanation
c)
Drillhole Data:Historical (pre-2007/8) drillhole data (inclusive of diamond, RC, and auger) exists on many of the
operations. However very little backing data is available for many of these older holes and it must
be assumed that QAQC was not included in the process. Minxcon has however reviewed the
general quality of the survey data for these drillholes. For the most part, collar data has been
found to agree well with local topography and is considered to be acceptable for modelling
purposes.
Downhole survey data with respect to diamond and RC drilling is also often absent from the older
holes; however, it should be noted that over 98% of these holes were seldom drilled to depths in
excess of 150 m and were vertically collared. Only 1.40% of all the drillholes on all the properties
were drilled as inclined drillholes, thus it is Minxcon’s view that the holes and their relative reef
intercept points would be spatially acceptable for modelling purposes.
The historical drillhole data has no accompanying assay QAQC, however this fact is considered
in allocation of Mineral Resource classification during modelling.
More recent drillhole data (inclusive of diamond, RC and auger) from 2008 onward is considered
to be of high quality as it was conducted to updated industry standards with the incorporation of
drillhole collar survey as well as assay QAQC where blanks and certified reference material were
inserted for monitoring purposes, with the inclusion of coarse duplicate samples. These later
drilling programmes were also either monitored, audited or managed by Minxcon personnel under
Minxcon previous sister company Agere Project Management (“Agere”).
Include
reference to
measures
taken to
ensure
sample
representivi
ty and the
appropriate
calibration
of any
measureme
nt tools or
systems
used.
d)
Trench, Sample Pit and Bulk Sampling (Vaalhoek Rock Dump):In order to evaluate the Vaalhoek Rock Dump, trenches and sample pits were dug. The trenches
and pits were surveyed by a Mine Surveyor and were sampled in sections down to a depth 1.2 m,
each sample representing a composite of 40 cm down the wall of the trench or pit. These samples
were then assayed. The discard material from the trenches and pits was then composited to form
a bulk sample of 50 tonnes for conducting size fraction analysis. The nature and quality of the
sampling in question has been considered in the Mineral Resource classification for the Vaalhoek
Dump, which is Inferred.
e)
Bulk Sampling (South East (DGs), Peach Tree, Ponieskrantz, Dukes Clewer):Bulk sampling was done through a triple deck screening plant (bulk samples were between 20t
and maximum 520t per waste rock dump).
f)
Trench Sampling (Theta Project Browns Hill):Trenching was conducted on Browns Hill during the 2017-2019 drilling campaign to assist in
locating the Lower Theta Reef outcrop. Trenches were dug in roughly an east-west orientation to
a depth of between 1.0 m to 2.1 m. A total of 10 trenches were dug with an approximate spacing
of approximately 30 to 35 m. The trenches were sampled near to vertical at 2 m intervals, due to
the very shallow dip of the reef, where full side-wall composite samples were taken. Samples were
dispatched to SGS Laboratory in Barberton for analysis. The trench sampling was not used in any
evaluation as its only purpose was to locate reef outcrops.
Chip Sampling:In concordant reef underground projects chip samples were taken normal to the reef dip and
calculated to give a composited value for a true reef thickness. In the case of cross-reefs such as
that at Rietfontein, chip sample positions were plotted on the development centre lines indicating
face sampling normal to the reef dip. Scatter plots were also generated to examine the data set
for errors introduced while capturing the data. All values were converted using factors of 2.54 cm
for 1 inch and 1.714285 g/t for 1 dwt.
a)
The older underground sampling took place at approximately 6 m spacing along on-reef
development, whilst in newer mining areas this spacing was reduced to approximately 2 to 3 m
along on-reef development. In the stoping areas a grid was targeted on an approximate 5 m by 5
m grid where applicable, which is a historical grid (Pre-1946). This grid was put in place due to
the nugget effect of the reef. The minimum size of the samples was 20 cm to obtain a minimum
weight of 500 g.
b)
Trench, Sample pit and Bulk Sampling (Vaalhoek Rock Dump):The trenches at Vaalhoek Rock Dump were located and spread as evenly as possible on the top
of the dump, while pits were located on the sides of the dump and these were sampled in sections
down to a depth 1.2 m, each sample representing a composite of 40 cm down the wall of the
trench or pit. The discard material from the trenches and pits was then composited to form a bulk
sample of 50 tonnes for conducting size fraction analysis and screened at -10 mm, +40 mm and
18
Criteria
SECTION 1: SAMPLING TECHNIQUES AND DATA
Detail
-75 mm. The nature and quality of the sampling in question has been considered in the Mineral
Resource classification for the Vaalhoek Dump, which is Inferred.
Explanation
c)
Aspects of the
determination of
mineralisation that
are Material to the
Public Report. In
cases where
‘industry standard’
work has been
done this would be
relatively simple
(e.g. ‘reverse
circulation drilling
was used to obtain
1 m samples from
which 3 kg was
pulverised to
produce a 30 g
charge for fire
assay’). In other
cases more
explanation may be
required, such as
where there is
coarse gold that
has inherent
sampling problems.
Unusual
commodities or
mineralisation types
(e.g. submarine
nodules) may
warrant disclosure
of detailed
information.
Drilling
techniques
Drill type (e.g.
core, reverse
circulation, openhole hammer,
rotary air blast,
auger, Bangka,
sonic, etc.) and
details (e.g. core
diameter, triple or
standard tube,
depth of diamond
tails, facesampling bit or
other type,
whether core is
oriented and if so,
by what method,
etc.).
Trench, Sample pit and Bulk Sampling (Theta Project):The trenches were dug in roughly an east-west orientation to a depth of between 1.0 m to 2.1 m.
A total of 10 trenches were dug with an approximate spacing of approximately 30 m to
Share your feedback
Discover